Influence of water stress on engineering characteristics and oil content of sunflower seeds

Scientific Reports volume 12, Article number: 12418 (2022) Cite this article

513 Accesses

1 Citations

1 Altmetric

Metrics details

Knowing some physical and mechanical characteristics and oil percentage of sunflower seeds could be useful for harvesting and processing equipment and activities such as transportation, storage, food production processes and establishing database of this seed. The main aim of this research was to study the effect of water stress during irrigation on seed's properties and quality. For this purpose, a field experiment was done under four deficit irrigation treatments [80%, 60%, 100–80 (100% irrigation requirement ETc to seed formation, and then reduced to 80% until harvesting) and 100–60% (100% ETc to seed formation, and then reduced to 60% until harvesting)] in comparable with full irrigation (100%). Geometrical, gravimetrical and mechanical characteristics as well as oil seed content and yield of sunflower seed were estimated. Result showed that there was no significant effect of low (100–80%) and medium (80%) irrigation deficit treatments on geometrical, gravimetrical and mechanical characteristics, while applying 60% of irrigation requirement (ETc) showed a significant effect on them. On the other hand, low and medium irrigation stress treatments improved the oil yield and seed oil content. The highest increase was 8.54% and 5.6% for oil yield and oil content respectively, considering T100–80 followed by applying 80% ETc, but with high water stress (60% ETc) oil yield and seed oil content significantly decreased.

Water is important in agricultural production, however in the near future, a water scarcity will have to be addressed. In semi-arid Mediterranean regions, water scarcity and rising rivalry for water resources between horticulture and other sectors compel the use of water management strategies that allow for water conservation while maintaining acceptable levels of production1,2.

Since sunflower has the capability to survive under stress condition than other oilseed crops to some extent, also water deficit in combination with high air temperature from flowering to grain filling stages significantly reduced the seed yield and seed oil quality of sunflower in the arid and semi-arid region3. Deficit irrigation is one of methods for increasing water use efficiency. Applying water deficit (80%)4 produced almost the same yield of sunflower seeds than that obtained from full irrigation, besides saving about 20% of irrigation water and maximized water use efficiency. Biological yield of safflower genotypes significantly reduced in drought stress by 17.9%, compared to normal condition5. Oil percentage is an important criterion for determining sunflower quality, and it can be influenced by irrigation deficits6. The oil content of sunflower seeds ranges from 37 to 42%4. According to prior research, when the sunflower crop was subjected to water stress during the flowering stage, the percentage of sunflower oil content reduced dramatically7. A decrease in safflower oil content with rising in drought has been reported by5 where the results showed a significant decrease of oil yield in drought stress conditions by 19.3%. In most of the cases oil yield reduction is less than seed yield reduction which indicates increase in oil contents. But severe drought at flowering and bud stage reduced oil yield more than seed yield which may be due to decrease in seed oil contents3. So these two stages may be regarded as the most sensitive to drought stress.

Because of the need of conserving and supplying water, many crops are now using tiny irrigation systems. Experiments have revealed that some plants respond positively to yield and its qualities, while others do not8.

Scientists are researching the physical, mechanical, chemical, and botanical aspects of seed from an engineering standpoint in order to improve seed production while maintaining high quality. These characteristics can be used to drive the design of seed production equipment and processes, such as planting, harvesting, processing, and testing specific cleaning and sorting machinery9,10,11. For instance, the size and shape of seeds are important for either their electrostatic separation from undesirable materials12. Also, the identification of seed shape could be important for an analytical prediction of its drying behavior13. Bulk density, true density and porosity are useful in sizing grain hoppers and storage facilities as they can affect the rate of heat and mass transfer during aeration and drying operations14. Data on the physical qualities of agro-food materials are significant because they may be used to input into models that anticipate product quality and behavior in sowing, handling, pre-harvesting, and post-harvesting circumstances; and they can help understand how food is processed15.

Shape and size, length, width, thickness, volume, geometric diameter, mathematical diameter, percentage of sphericity, flat surface area, transverse surface area of individual seeds, stiffness force, resting angle, friction coefficient, terminal velocity of threshed head components, drag coefficient, real density, and bulk density are the most important properties affecting sunflower seeds. In addition, the width of the head, the number of seeds per head, and the weight of 1000 seeds are the most essential properties affecting the head16.

The results of physical and mechanical properties of sunflower seeds showed a variation of 14.32 to 31.00 mm for length, 4.7 to 9.8 mm for width and 2.7 to 6.6 mm for thickness of sunflower seeds. The values of 1000 seed mass, volume, true density, bulk density and porosity were between 149.8–167.7 g, 99.05–628.9 mm3, 444.5–521.8 kg/m3, 269.06–275.57 kg/m3 and 39.09–47.18% respectively. The rupture force, deformation, and absorbed energy increased with increase in moisture content from 1.8 to 14.5%, while decreased with further increasing of moisture content from 14.5 to 20.3%. The mean value of percentage of physically damaged seeds increased from 2.75 to 10.81% with increasing the impact velocity from 40.8 to 62.3 m/s. In both impact orientations, the total damaged seeds increased with increase in impact velocity for all moisture contents of seeds12,17,18,19.

There has been research on the engineering properties of sunflower seeds15,16,20, but little is known about how agricultural techniques affect engineering properties such as water stress. Irrigation and planting systems might also have an impact on seed properties4.

The goal of this research is to find out how using water stress systems influences sunflower plant engineering features, productivity, and seed oil yield. So, if some deficit irrigation treatments have a positive effect on productivity and seed oil yield, then an amount of water can be saved.

To meet the goals of this study, a field experiment utilizing the sunflower hybrid Sakha 53 was undertaken at a private farm in Qalyubia Governorate, Egypt, during two successeve growing summer seasons of 2019–2020 (Permissions were obtained from Egyptian Ministry of Agriculture and experimental research and field study was comply with relevant institutional, national, and international guidelines and legislation). This site exemplifies the Nile Delta's clay soil conditions. Sunflowers have a growing seasons that lasts from June to September. Throughout the profile, the dominating soil at the experimental location was clay-textured (2.45% coarse sand, 18.55% fine sand, 27.77% silt and 51.23% clay). The region is arid characterized, during that time of year, by no rainfall, a high average temperature and a relatively medium humidity resulting in a medium to high evaporative demand.

The experimental site was divided to five plots (one for each irrigation treatment) have a width of 3 m and extend over a length of 25 m with 2 m separation line between plots. Seeds were planted at 30 cm between plants with spacing 60 cm between rows, that is, each plot is divided into five rows, and each row is considered a replication.

For irrigation was used polyethylene (PE) laterals of 16 mm diameter with 4 L/h built-in drippers at 30 cm apart were used with one lateral for each row. The control valves were installed at the inlet of each treatment to control the flow of water. One bar pressure was maintained using 0.75 kW pump.

The treatments for irrigating the sunflower crop were full irrigation at 100% of crop requirement (ETc) and four water deficit regimes [80% ETc, 60% ETc, (100–80% ETc) and (100–60 ETc) denoted as T100, T80, T60, T100–80, and T100–60, respectively]. The T100–80 and T100–60 treatments were applied as 100% ETC to seed formation and then reduced to 80% and 60% ETc until harvesting, respectively.

Values of daily evapotranspiration (ETo) were obtained from data predicted by Central Laboratory for Agricultural Climate (CLAC) which are always available 5 days beforehand. Kc for sunflower during the growing season was obtained from FAO (2015). The obtained ETo and Kc were used to calculate water requirement for sunflower ETc (mm) as described by21.

The irrigation starts on all treatments when 75% of the available water under 100% ETc irrigation treatment is consumed. All other agricultural practical for sunflower crop was used as recommended by the Agriculture Ministry.

At harvest time, the heads of 15 plants were randomly drawn from each plot and were separately harvested, bagged, and dried under the sunshine for one week. Half of harvested seeds used for measuring oil yield and the other half used for measuring seed physical and mechanical characteristics.

Sunflower oil yield per unit area is result of seed yield per unit area and the oil percentage of seed. Using the Soxhlet equipment and petroleum ether 40–60 °C as a solvent, the seed oil percentage was measured. The powdered samples were soaked in n-hexane 64–68 °C for 48 h with periodic shaking after being air-dried samples of sunflower seeds were milled twice in a stainless-steel experimental mill. The food was immersed in the same solvent for a second time for another 24 h. The mixed extracts were filtered through sufficient amounts of Anhydrous Sodium Sulphate and then vacuum-distilled to remove the solvent22.

To obtain the moisture content, 50 g of seeds for each treatment were selected and placed for 24 h at 72 °C in the oven and in accordance with ASAE Standard23 moisture was measured on the basis of dryness (d.b).

Mass of three groups of 1000 seeds for each sample was measured using a balance with an accuracy of 0.001 g. The seeds size were measured for three groups of 100 seeds by a caliper with accuracy of 0.01 mm. Because the shape of the seeds is irregular granular, seed size is expressed by geometrical diameter (dg) as following20:

where: T, W and L are the thickness, width and length of the seed. In addition, surface area (S), volume (Vs) and sphericity coefficient (Ø) of seeds, were determined using following equation17:

Filling a container with 500 mL of seeds from a height of 15 cm, hitting the top edge, and measuring the contents, the bulk density (Pb) was estimated 3 times for each sample. The true density (Pt) of a substance is defined as the ratio of its mass to its actual volume. Liquid displacement method was used to determine true density, and toluene fluid (C7H8) was used due to the low absorption of liquid by the seed. A certain mass of seed was poured into a cylindrical container having a volume of 100 mL. Then, the volume of transferred toluene was recorded, and the true density of the seeds was determined using the mass ratio of the seed to the displaced liquid volume24. The porosity (Pf) of bulk seeds is defined as the proportion of space that is not occupied by the seeds. The percentage of porosity was calculated using the formula below12.

The crushing load plays a very important role in the design of loading and unloading equipment, storage systems, harvesting machines and drying equipment, conveyors, spouting and free falling equipment, because seeds are affected by other metallic, wood and plastic surfaces during operations in this equipment, which can result in mechanical damage13, whereas oil expulsion could be used for rupture force and rupture energy17.

To assess the impact of the loading direction on the rupture, the seeds were placed vertically, with the seed's main axis in line with the loading direction, and horizontally, with the main axis perpendicular to the loading direction, using the Instron Universal Testing Machine (Fig. 1)14.

Crushing load testing machine as described by Khodabakhshian et al.14.

Using the emptying approach, the seeds’ repose angle (θ) was calculated in a bottomless cylinder (diameter 5 cm; height 10 cm). The cylinder was filled with sunflower seeds and gradually raised until a heap was produced on a table with three distinct surfaces (wood, stainless steel, and plastic). The heap's diameter (D) and height (H) were measured and repose angle (θ) was calculated as reported by25:

Static friction coefficients (μ) on the three different surfaces (wood, stainless steel, and plastic) were calculated for seed. These surfaces are widely used in seed processing and handling25. Static friction coefficients were calculated as a tangent of slope angle (angle of repose)26:

The variation of the length, width, thickness, and moisture content, of the sunflower seed at different irrigation treatmens are shown in Tables 1 and 2. The results showed that all these parameters decreased with increasing the water deficit. The moisture content of seeds was affected by water stress, where it decreased from 7.92% at T100 to 5.49% at T60. All dimensions have a similar tendency. The average length, width, and thickness decreased by 14%, 7.6%, and 7.1%, respectively. In addition, the 1000 seed mass decreased by 9.8% with applying the T60 treatment compared to the T100 treatment. The geometric mean diameter, volume, and surface area had the same behavior as shown in Table 2. These behaviors may be due to the complexity of water stress impacts on seed moisture content as reported by17,27. The reduction trend in dimensions with seeds' moisture content was due to the filling of capillaries and voids upon absorption of moisture and subsequent swelling as described by15. The variation of the length, width, thickness, geometric mean diameter and sphericity, of the sunflower seed increased with increasing moisture content from 3 to 14% d.b for all size categories. This indicates that during the moisture absorption process, the sunflower seed will simultaneously expand in all dimensions as reported by14,19.

The majority of widths are about 1.5 thicknesses, and the elongation indicates that sunflower seeds have a low oblong shape. Sunflower seeds, on the other hand, are more likely to roll than slide due to their medium elongation ratio. This was also revealed by the sphericity data in Table 2. This information could be useful in the design of separators, and conveyer equipment. The mean values of sphericity of the sunflower seeds used in this study were much higher than those reported by18, while the sphericity values for the sunflower seeds were in the same ranges compared with those of this study28. The calculated porosity decreased from 41.6% (T100) to 38.1% (T60) when moisture content decreased from 7.9 to 5.5% (w.b.) that affected by water stress. The form of the plot was similar to those were observed by20. Also, the geometrical diameter (dg), surface area (S) and volume (Vs) were take the same trend.

Coefficients of static friction of seed on studied surfaces increased from 0.380 to 0.424 as water stress increased from T100 to T60 as shown in Table 3. This may be explained by increased cohesive force of seeds with the surface because of the dimensions shrank that happened as result of water stress. The results showed that the highest value of static coefficient of friction was on the wood surface, followed by plastic, and stainless steel surfaces at the same water stress for all treatments. In addition, the higher coefficients for high water stress might be attributed to its lower sphericity of shape compared with that of full irrigated (T100). The variation of the angle of repose take the same trend, where it increased by 9.5% (stainless steel), 4.3% (plastic) and 4% (wood) as water stress increased from T100 to T60. The angle of repose increased linearly with an increase in the water stress because seeds might stick together which results in less flowability and better stability, thereby increasing the angle of repose. Similar findings were reported for sunflower seed and kernel14,17, and sesame19.

The obtained results of crushing load (Table 4) shows that the greater values were in the vertical direction than horizontal direction for all investigated treatments. The maximum crushing load reaches 63.1 and 25.0 N for T100, while the minimum value was 46.2 and 21.4 N for T60 for both vertical and horizontal directions respectively.

The crushing load increases as the seed size increases, maybe because the seed contact area with the loading plates expands, resulting in the expansion of low stress. This is consistent with Hertz's compression test theory for food items14. Both orientations exhibit the same trend of increased crushing load as the moisture content rises from 5.49% (T60) to 7.92% (T100). These findings are consistent with those of20, who discovered that raising the moisture content of sunflower seed from 3 to 8% d.b increases the crushing load. This could be explained by the gradual change in the integrity of the cellular matrix or cellular structure of seeds19.

When full irrigation was applied to seed formation and then reduced to 80% ETc until harvesting (Table 5), the highest oil percentage (40.32%) was recorded, followed by T80 for the entire growing season (39.67%), and the lowest percentage (36.12%) when plants were subjected to water stress T60. There was no substantial effect on oil seed content when water stress occurred after the seed filling stage29. The decrease in oil percentage in the control treatment (T100) could be due to increased water consumption, which leads to excessive vegetative growth and delayed maturation of immature seeds at harvest time. The decrease in oil percentage in the severe stress treatment could be due to impaired seed filling, which causes the skin of sunflower seeds to thicken27,30. It has been quoted that the oil percentage does not damage in low water stress4.

The intensity of oil yield change depends on the growth stage of the crop and the percentage of water reduction. The oil yield of sunflower was affected by drought stress, with the low status treatment yielding 8.6% for T60 less than the control treatment, while oil yield was increased by 8.5% for T100–80. Water stress during the flowering stage was found to be a limiting factor for seed filling, resulting in a significant reduction in oil yield31,32. The effect of water scarcity on seed oil yield also emphasizes the importance of attention to water stress potential in different sunflower genotypes.

The physical and mechanical properties are important to be known for post-harvest technology, and deficit irrigation has to be used as effective method for water saving. Comparing the irrigation treatments from a physical and mechanical properties point of view, all physical and mechanical parameters studied in this research were close to each other under all treatments except under 60% ETc treatment when all parameters were decreased significantly. The repose angle increased from 21° to 26° whereas, the coefficient of static friction varied from 0.380 to 0.488 over different material surfaces in the specified water stress. On the other hand, low and medium irrigation deficit treatments improved the oil yield and its oil content. The highest increase for oil yield and seed oil content were under applying T100–80 (100% ETc to seed formation, and then reduced to 80% until harvesting) followed by applying 80% ETc, but with high water deficit (60% ETc) oil yield and seed oil content significantly (P ≤ 0.05) decreased.

All data generated or analysed during this study are included in this published article.

Costa, J. M., Ortuno, M. F. & Chaves, M. M. Deficit irrigation as a strategy to save water: Physiology and potential application to horticulture. J. Integr. Plant Biol. 49, 1421–1434 (2007).

Article Google Scholar

Hassan, A. M. & Abuarab, M. Effect of deficit irrigation on the productivity and characteristics of tomato. ASABE Annu. Int. Meet. 131597701, 1–15. https://doi.org/10.13031/aim.20.St.Joseph,Mich.:ASABE (2013).

Article Google Scholar

Hussain, M. et al. Drought stress in sunflower: Physiological effects and its management through breeding and agronomic alternatives. Agric. Water Manag. 201, 152–166. https://doi.org/10.1016/j.agwat.2018.01.028 (2018).

Article Google Scholar

Mostafa, H., El-Ansary, M., Awad, M. & Husein, N. Water stress management for sunflower under heavy soil conditions cooling effectiveness. Agric. Eng. Int. CIGR J. 23(2), 76–84 (2021).

Google Scholar

Joshan, Y., Sani, B., Jabbari, H., Mozafari, H. & Moaveni, P. Effect of drought stress on oil content and fatty acids composition of some safflower genotypes. Plant Soil Environ. 65, 563–567. https://doi.org/10.17221/591/2019-PSE (2019).

Article CAS Google Scholar

Han, Y., Yang, H., Wu, M. & Yi, H. Enhanced drought tolerance of foxtail millet seedlings by sulfur dioxide fumigation. Ecotoxicol. Environ. Saf. 178, 9–16 (2019).

Article CAS Google Scholar

Hamid, R. M. & Abolfazl, T. Effect of water stress on quantitative and qualitative characteristics of yield in sunflower (Helianthus annuus L.). J. Novel Appl. Sci. 2, 299–302 (2013).

Google Scholar

Iqbal, H., Yaning, C., Waqas, M., Shareef, M. & Raza, S. T. Differential response of quinoa genotypes to drought and foliage-applied H2O2 in relation to oxidative damage, osmotic adjustment and antioxidant capacity. Ecotoxicol. Environ. Saf. 164, 344–354 (2018).

Article CAS Google Scholar

Mohsenin, N. N. Physical Properties of Plant and Animal Materials (Gordon and Breach Science Publishers, 1986).

Google Scholar

Tayle, S. A., El-Nakib, A. A., Zaalouk, A. K. & Ahmed, A. Some physical properties of apricot pits. Misr J. Ag. Eng. 28(1), 149–165 (2011).

Google Scholar

Werby, R. A. & Mousa, A. M. Some physical and mechanical properties of Jatropha fruits. Misr J. Agric. Eng. 33(2), 475–490 (2016).

Article Google Scholar

Gamea, G. R. Physical properties of sunflower seeds components related to kernel pneumatic separation. Int. J. Eng. Technol. 13, 1 (2013).

Google Scholar

Sigalingging, R., Herak, D., Kabutey, A., Divisova, M. & Statonova, T. A review of the physical, mechanical, thermal, and chemical properties of Jatrophacurcas seeds as basic information for oil pressing. Int. Refer. Res. J. 5(1), 44–53 (2014).

Google Scholar

Khodabakhshian, R., Emadi, B. & Abbaspour, M. H. Some engineering properties of sunflower seed and its kernel. J. Agric. Sci. Technol. 4(4), 37–46 (2010).

Google Scholar

Seifi, M. R. Moisture-dependent physical properties of sunflower seed (SHF8190). Mod. Appl. Sci. 4, 7 (2011).

Google Scholar

El-Raie, S., Nasr, G., El-Ebaby, F., & El-Adawy, W. Study of some physical and engineering properties for sunflower heads and seeds concerning the design of threshing devices. 6th Conference of Misr Society of Agriculture Engineering, 21–22, 153–176 (1998).

Malik, M. A. & Saini, C. S. Engineering properties of sunflower seed: Effect of dehulling and moisture content. Cogent. Food 2, 1145783. https://doi.org/10.1080/23311932.2016.1145783 (2016).

Article CAS Google Scholar

Jafari, S., Khazaei, J., Arabhosseini, A., Massah, J. & Khoshtaghaza, M. Study on mechanical properties of sunflower seeds. Electron. J. Polish Agric. Univ. (EJPAU) 14, 1–10 (2011).

Google Scholar

El-Sayed, A., Abd El-Wahab, M. K., El-Shal, H. & Abd Allah, W. E. Effect of moisture content on physical and engineering properties of some seeds. Zagazig J. Agric. Res. 48(2), 387–399 (2021).

Article Google Scholar

Gopta, R. K. & Das, S. Physical properties of sunflower seeds. J. Agric. Eng. Res. 66(P1–8), 1996 (1996).

Google Scholar

Keipp, K., Hütsch, B. W., Ehlers, K. & Schubert, S. Drought stress in sunflower causes inhibition of seed filling due to reduced cell-extension growth. J. Agric. Crop Sci. https://doi.org/10.1111/jac.12400 (2020).

Article Google Scholar

Barthet, V. J. & Daun, J. K. Oil Content Analysis: Myths and Reality (AOCS Press, 2004).

Book Google Scholar

ASAE. Moisture Measurement: Unground grain and seeds. Am. Soc. Agric. Eng. S 352, 2 (1999).

Google Scholar

Jan, N. K., Panesar, P. S. & Singh, S. Effect of moisture content on the physical and mechanical properties of quinoa seeds. Int. Agrophys. 33, 41–48. https://doi.org/10.31545/intagr/104374 (2019).

Article CAS Google Scholar

Kabas, O. & Vladut, V. Determination of some engineering properties of pecan (Carya illinoinensis) for new design of cracking system. Erwerbs-obstbau 58, 31–39 (2016).

Article Google Scholar

Bahnasawy, A. & Mostafa, H. Some engineering properties of different feed pellets. Misr. J. Agric. Eng. 28, 4. https://doi.org/10.21608/MJAE.2011.102604 (2011).

Article Google Scholar

Dehkhoda, A., Naderidarbaghshahi, M., Rezaei, A. & Majdnasiri, B. Effect of water deficiency stress on yield and yield component of sunflower cultivars in Isfahan. Intl. J. Farm Alli. Sci. 2(S2), 1319–1324 (2013).

Google Scholar

Khazaei, J., Sarmadi, M. & Behzad, J. Physical properties of sunflower seeds and kernels ralated to harvesting and dehulling Lucrari Stiintifice Vol. 49 (Seria Agronomie, 2006).

Google Scholar

Bashir, M. A. & Mohamed, Y. M. Evaluation of full and deficit irrigation on two sunflower hybrids under semi-arid environment of Gezira, Sudan. J. Agric. Food Appl. Sci. 2, 53–59 (2014).

Google Scholar

Krizmanić, M., Liović, I., Mijić, A., Bilandžić, M. & Krizmanić, G. Genetic potential of OS sunflower hybrids in different agroecological conditions. Sjemenarstvo 20(5/6), 237–245 (2003).

Google Scholar

Iqbal, N., Ashraf, M. Y. & Ashraf, M. Influence of water stress and exogenous glycinebetaine on sunflower achene weight and oil percentage. Int. J. Environ. Sci. Technol. 5(2), 155–160 (2005).

Article Google Scholar

Zamani, S., Naderi, M. R., Soleymani, A. & Nasiri, B. M. Sunflower (Helianthus annuus L) biochemical properties and seed components affected by potassium fertilization under drought conditions. Ecotoxicol. Environ. Saf. 190, 110017. https://doi.org/10.1016/j.ecoenv.2019.110017 (2020).

Article CAS PubMed Google Scholar

Download references

Open access funding provided by The Science, Technology & Innovation Funding Authority (STDF) in cooperation with The Egyptian Knowledge Bank (EKB).

Agricultural and Biosystems Engineering Department, Faculty of Agriculture, Benha University, Moshtohor, Qalyobia, Egypt

Harby Mostafa & Mohamed T. Afify

You can also search for this author in PubMed Google Scholar

You can also search for this author in PubMed Google Scholar

All authors wrote the main manuscript text and reviewed the manuscript.

Correspondence to Harby Mostafa.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Mostafa, H., Afify, M.T. Influence of water stress on engineering characteristics and oil content of sunflower seeds. Sci Rep 12, 12418 (2022). https://doi.org/10.1038/s41598-022-16271-7

Download citation

Received: 05 April 2022

Accepted: 07 July 2022

Published: 20 July 2022

DOI: https://doi.org/10.1038/s41598-022-16271-7

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.